PB-S-S-1WS

Ø potencia sin carga consumo

Ø entrada de ca universal rango (90 ~ 264Vac) Ø alta eficiencia, larga vida y alta confiabilidad Ø salida protecciones: OVP / OLP / SCP Ø amplia temperatura ambiente de funcionamiento (-25 ℃ ~ 70 ℃) Ø se puede instalar en TS-35 / 7.5 o 35 / 15 Ø 100% carga completa quemado prueba Ø PCB con conforme revestimiento Ø adecuado para aplicaciones críticas Ø enfriamiento por convección de aire libre Ø 3 años de garantía especificación modelo DG-30-S12 DG-30-S24 salida salida dc 12V 24V Corriente nominal 2.5A 1,25A CurrentRange nota 1 0 ~ 2.5A 0 ~ 1,25A ondulación y ruido nota 2 10 ~ 50 ℃ ≤50mV ≤70mV -25 ~ 10 ℃ ≤100mV ≤140mV voltaje ADJ. rango 12 ~ 14V 24 ~ 28V precisión de voltaje ± 1,0% Regulación de línea ± 0,5% Regulación de carga ± 1% Configuración hora

Ø entrada de ca universal rango (90 ~ 264Vac) Ø 300Vac aumento durante 3 segundos Ø alta eficiencia, larga vida y alta confiabilidad Ø salida protecciones: OVP / OLP / SCP Ø amplia temperatura ambiente de funcionamiento (-25 ℃ ~ 50 ℃) Ø se puede instalar en TS-35 / 7.5 o 35 / 15 Ø 100% carga completa quemado prueba Ø PCB con conforme revestimiento Ø adecuado para aplicaciones críticas Ø enfriamiento por convección de aire libre Ø 3 años de garantía especificación modelo DG-60-S12 DG-60-S24 DG-60-S48 salida salida dc 12V 24V 48V Corriente nominal 5A 2.5A 1,25A CurrentRange nota 1 0 ~ 5A 0 ~ 2.5A 0 ~ 1,25A ondulación y ruido nota 2 10 ~ 50 ℃ ≤60mV ≤50mV ≤120mV -25 ~ 10 ℃ ≤120mV ≤100mV ≤240mV voltaje ADJ. rango 12 ~ 14V 24 ~ 28V 48 ~ 56V precisión de voltaje ± 1,0% Regulación de línea ± 0,5% Regulación de carga ± 1% Configuración hora

Ø  High voltage input, 176~264Vac Ø  High Efficiency, long life and High reliability Ø  Output protections: SCP/OVP/OLP/OPP Ø  Wide operating ambient temperature (-25℃~65℃) Ø  All using 105℃ long life electrolytic capacitors. Ø  100% full load burn-in test Ø  2 years warranty             Ø  Isolated Dual Outputs MODEL CMG-H150D24G+12-M OUTPUT DC Output V1 24V V2 12V Rated Current V1 6A V2 5A      Current Range  Note 3 V1 0.5~5.0A(5.0Ais recommended) V2 0.3~3.0A(3.0Ais recommended) Ripple and Noise Note4 0~65℃ V1 240mV V2 120mV Ripple and Noise -25~0℃ V1 480mV V2 240mV Voltage ADJ.  Range 21.6~26.4V Voltage Accuracy V1 ±1.0% V2 ±10.0% Line Regulation V1 ±0.5% V2 ±1.0% Load Regulation V1 ±3.0% V2 ±10.0% Set-up Time ＜1.5S (220Vac input, V1 @ 5A, V2 @ 3.0A) Hold up Time ＞20mS(220Vac input, V1 @ 5A, V2 @ 3.0A) Temperature Coefficient ±0.03%/℃ Overshoot and Undershoot <5.0% INPUT Voltage Range   176Vac~264Vac Frequency Range 47Hz--63Hz Efficiency ( Typical) ≥80% (220Vac input, V1 @5A, V2 @3.0A) AC Current (max.) <1.9A Inrush Current (Typical) <50A@220Vac      Cold start Leakage Current Input—output:<0.25mA     Input—PG:<3.5mA PROTECTION Over Power 157~225W, Hiccup mode, auto recovery Over Current V1: 5.5~8.0A, Hiccup mode, auto recovery Over Voltage V1: 25.2~36V, Hiccup mode, auto recovery Short Circuit Long-term mode, auto recovery ENVIRONMENT Operating amb. Temp. & Hum. -25℃~65℃;  20%~90%RH  No condensing Storage Temp. & Hum. -30℃~85℃;  10%~95%RH  No condensing SAFETY &EMC   (Note 5) Safety Standards GB4943/ EN60950 Withstand Voltage Primary-Secondary:3.0KVac /10mA .Primary-PG:1.5KVac/10mA. Secondary-PG: 0.5KVDC/10mA.  Output V1—V2: 0.5KVDC/10mA. Test time:1 min Isolation Resistance 10M ohms EMI Conduction&Radiation Compliance to EN55022, CLASS B Harmonic Current Compliance to EN61000-3-2，CLASS A EMS Immunity Compliance to EN61000-4-2,4,5,8,11; OTHERS MTBF (MIL-HDBK-217F) More than 200,000Hrs (25℃, Full load) Dimension  (L*W*H) 199×99×38mm Packing 20PCS/CTN, 15KGS, 0.04cbm Cooling method Cooling by free air convection NOTE   1.     Total output power can’t exceed 150W, Label is marked by the Max current. Recommend the loading is 24V/5A,12V/3.0A.  2.     All parameters NOT specially mentioned are measured at rated input, rated load and 25℃ of ambient temperature. 3.     Measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1 uF & 47uF parallel capacitor. 4.        The SPS is considered a component which will be installed into final equipment. The equipment must be re-confirmed that it still meets EMC directives.